WIDE INPUT VOLTAGE RANGE
A wide range from 1HP (0.75KW) to 30HP (25 KW)
Certified by Underwriter Laboratories
96.7% overall efficiency helps extract maximum power from solar panels
2 year replacement warranty extendable to 5 years
Starting input upto 5HP is 150VDC and 12.5HP is 400VDC.
Works with any kind of 3 phase pump including rewound pumps
Automatic mains changover when grid is not available
Built in MPPT with >99% efficiency
Simple to install and operate. Compact in size with wall hanging facility
Tested till 1000ft depth & 30000ft horizontal for 5HP and above
Use remote monitoring using WIFI, ZIGBEE or GSM to monitor power generation & other metrics
LCD screen displays all solar parameters including energy generation
Tested successfully with drip irrigation systems
2 IN 1
Use the same panels to charge batteries too using our proprietory technology
DSP based technology
Water proof and dust proof. Can be used directly outdoors.
Large heat sinks for heat dissipation and continous functioning
Built in protections for dry run, surge, reverse polarity and short circuit
Operating temperature range of -10C to 60C
IGBT switching element
I WANT TO RUN MY EXISTING PUMP IN SOLAR. HOW DO I DO IT?
If you already have a 3 phase pump simply connect the FIRESTAR solar water pump controller to your well pump or pool pump and a set of solar panels to run your existing pump on solar power.
I HAVE A SINGLE PHASE PUMP. WHAT DO I DO?
Single phase pumps are inherently inefficient to run on solar power as the pump cannot be run efficiently under less than optimal sunlight conditions. Rather than add more panels to make it run better, it is simply cheaper to replace the pump with a 3 phase pump
WHY SHOULD I CHOOSE THE FIRESTAR SOLAR WATER PUMP CONTROLLER WHEN I CAN CHOOSE VFD PRODUCTS FROM TOP COMPANIES?
The FIRESTAR solar water pump controller has an efficiency of 96.7% (as certified by Underwriter Laboratories) which is much higher than VFD products at 85%. This means you can generate a similar amount of power from 20% less solar panels.
The FIRESTAR solar water pump controller starts at lower voltages i.e upto 5HP the pump controllers starts at 150V while drives start at around 300V. This means you can start pumping much earlier and stop pumping much later using the FIRESTAR pump controller.
Also, we have all protections built in which are expensive extras while using a VFD.
Lastly, the FIRESTAR pump controller is IP65 compliant which means you dont have to spend on an external enclosure which you have to while using a VFD.
WHAT ADDITIONAL EQUIPMENT DO I HAVE TO PURCHASE TO MAKE THE SYSTEM FUNCTIONAL?
Just solar panels & wires. All protections are built in so you dont need to purchase it. The wide voltage range allows panels to be setup in any configuration under most circumstances so junction boxes can be avoided. And because the sytem is IP65 you save money on an enclosure.
CAN I RUN MY PUMP USING THE GRID IN CASE SOLAR POWER IS INSUFFICIENT?
The FIRESTAR solar water pump controller has an optional automatic changeover facility that will switch over to the grid in case it is unable to run your pump using existing sunlight conditions. Optionally, you can also add a switch and manually change it to the grid.
CAN I MONITOR MY SOLAR WATER PUMP REMOTELY?
Definitely. We can provide you with a login id and password to our remote monitoring website from where you can monitor the functioning of the FIRESTAR solar water pump controller.
WHEN I AM NOT USING THE PUMP, CAN I CHARGE MY EXISTING BATTERIES WITH THE SOLAR PANELS?
Definitely. Just use our FIRESTAR off grid solar inverter. These inverters are capable of lowering the high input voltages of these panels to as low as 24V which can be stored in just 2 batteries. If you already have en existing inverter, just use the FIRESTAR MPPT to do the same.
DO I HAVE TO PERFORM SOFTWARE CONFIGURATIONS TO MAKE THIS WORK?
No. Our sophisticated software algorithms automatically works with the panels and the pump and configures itself accordingly. Installation is as simple as PLUG & PLAY